www.SunStreamSaunas.com 1 - 888 262 4477Assembly Manual
Prepare & Position the Sauna FloorIf you are assembling your sauna on a hard surface floor it is recommended that you applythe included adhesive felt to the bottom of the sauna floor.It is important that the sauna floor is level. Checking with a large level isrecommended. If the floor is not level, shimming or other remedies should beapplied before assembling the sauna.Place the sauna floor in the desired location. It is necessary to position the floor out fromyour walls for assembly and slide the sauna into final position following assembly. www.SunStreamSaunas.com 1 - 888 262 4477
Position the Front WallLift the front wall into positioncarefully lowering the bottom ofthe wall into the channel on thefloor base. Prop up one end ofthe front wall to enableconnection of the door heaterelectrical lead.Before installing the Front Wall, ensure that thedoor heater electrical is protruding from bottom ofFront Wall frameA bit of plastic wrap can serve to hold theconnector out slightly.www.SunStreamSaunas.com 1 - 888 262 4477
Connect door heater electrical lead to the floor base.Ensure hat the threaded cuff is fully screwed onto the floor base connector.NOTE:Be sure that the wire's connector is fully inserted into the floor base connector and that thethreaded cuff is fully screwed onto the floor base connector.Position Right Side WallLift the Right Side Wall into positionwedging the bottom of the wall intothe channel in the floor base.www.SunStreamSaunas.com 1 - 888 262 4477
Connect Side & Front WallCinch the two walls together byapplying pressure on the outsideof the side wall with your knee Slide the side wall upward approx.3/4” while holding the front walldownIt is helpful if a second person applies pressure against the opposite edge of the frontwall. This will help ensure that the two walls remain in contact and the fastenersconnect.The 2 sets of fasteners for thewalls will connect when theSide Wall is raised sufficiently. When you feel the fasteneresconnect, slide the Side Walldown while continuing to cinchthe two walls together.www.SunStreamSaunas.com 1 - 888 262 4477NOTE: It is NOT necessary to lift the entire Side Wall. Simply slide the Side Wallupward at the front corner of the sauna to connect to the Front Wall
Repeat procedure to connect the Back Wall to theRight Side Wall. Raise the side wall up approx 3/4".NOTE: Do not raise the Side Wall any further thannecessary. Raising the Side Wall too much maydisrupt the connected front corner Check to ensure that both sets of fasteners have connected by looking at the cornerinside of the sauna. It is possible to connect one set of fasteners and miss the other.If there is an obvious gap in the corner between the two walls the fasteners have notconnected and the raising and lowering procedure will need to be repeated. RIGHTSIDEWALLBACKWALLPosition the Back WallLift the Back Wall into position wedging the bottomof the wall into the channel in the floor base.www.SunStreamSaunas.com 1 - 888 262 4477NOTE: It is NOT necessary to lift the entire Side Wall. Simply slide the Side Wallupward at the back corner of the sauna to connect to the Back Wall
Position Left Side WallLift the Left Side Wall into position,wedging the bottom of the wall intothe channel in the floor base.Repeat the raising up and sliding down procedure again to connect the Left Side wall toBack Wall and the the Left Side Wall to the Front Wall. Connect one corner at a time. Raise Side Wall upwww.SunStreamSaunas.com 1 - 888 262 4477Back Wall Side Wall
Prepare to install the sauna roofPull the single plastic connector down and out of the roofbefore lifting the roof into place. If you are unable to grabhold of the connector through the small opening in theceiling, it may be necessary to remove the first T&G boardon the top left side of the roof and feed the connector downthrough the opening. Install the Sauna RoofLift the roof up and over top of the sauna walls. If you are installing the sauna in a restrictivespace and are unable to walk down the sides of the saunas, it may be necessary for oneperson to go inside the sauna. Hook the right side of the roof over the Right Wall then lower the roof toward the left of thesauna.www.SunStreamSaunas.com 1 - 888 262 4477
Connect Roof WiresBefore lowering the roof, connect the 12 V power supply wires. This is easiest accomplished with one person holding the weight of the roof while the othersnaps together connectors and then feeds the connector up into roof. Lower Roof intoPositionThis wire brings powerto the roof for thestereo and lightingcomponentswww.SunStreamSaunas.com 1 - 888 262 4477Under-Bench ElectricalNOTE: Do not connect main power cord to your wall outlet yet at this time.Connect the circular connector topower supply box. Align the groovein connector to properly insert.Thread the cuff of connector on fullyAttach the 'D-Sub' computerstyle connector as shown
Plug in all heater leads to receptaclesin the power supply box.www.SunStreamSaunas.com 1 - 888 262 4477Feed the main power supply cord in through the hole in back wall and insert in powersupply box. DO NOT plug power cord into your wall outlet until all electrical connectionsare complete inside of the sauna. Connect circular connector forthe door heater. Ensure that the connector is fully insertedand that the cuff of connector is fullythreaded on.
Power Supply CordFeed the main power supply cord in through the hole in back wall and insert in to the powersupply box. Connect main power cord to your wall outlet when all electrical connectionsinside of the sauna and the roof are complete.www.SunStreamSaunas.com 1 - 888 262 4477ChromatherapyThe Chromatherapy LEDpanel is controlled by theremote control and is NOTconnected to the sauna wallcontrol panel.
Remove Side Wall Heater GuardsThe wooden lattice work in front of the heaters isreferred to as the heater guard. These are held on with strong magnets. It is necessary to remove the heater guards from thetwo side walls in order to install the leg heater andthe sauna bench.Leg HeaterInstall the leg heater by lowering it into the bracketsmounted on the side walls.Plug leg heater into the powersupply box in floor.www.SunStreamSaunas.com 1 - 888 262 4477
www.SunStreamSaunas.com1-888 262 4477The metal shielding on the underside of thesauna bench is part of the Evolve EHS electricfield mitigation system.When installing the bench connect the yellow,green striped wire with its mate from the powersupply box. This is simply a grounding wire anddoes not carry any mains power.
Install BenchThe bench in your new sauna isreversible. Choose whichever sideappeals to you to face upward.Reinstall the side wallheater guardsInstall the door handlewww.SunStreamSaunas.com 1 - 888 262 4477
www.SunStreamSaunas.com 1 - 888 262 4477 Heater GuardsThe heater guards in your new Sun Stream Infrared Sauna are held to the wall withstrong earth magnets. If preferred, the heater guards can be screwed directly to the wallfor a more permanent and secure attachment. The heater guards are pre-drilled for theattachment screws.Screws are included to attach the heater guard to the wall. Select a drillbit with a smaller diameter than the screw threads to drill a pilot hole
www.SunStreamSaunas.com 1 - 888 262 4477 Drill a pilot hole into the wall throughthe holes in the heater guards.Do notdrill deeper than necessary for thelength of the screw. NOTE: The pilot holes are importantto ensure that the tongue and groovewall boards do not split wheninstalling screws.Install screws to firmly attach heater guard to the wall
www.SunStreamSaunas.com 1 - 888 262 4477 Ensure that the legs' ends are flushwith the bottom edge of the framesConnect bench legs to the insidecorners of the frames using suppliedwood screws.Attach the leg assembly to the bottom of the bench surface.Choosewhich surface of the bench you prefer to be the top and bottom.Option-L Movable Bench Assembly
www.SunStreamSaunas.com 1 - 888 262 4477Audio System Music can be piped to the speakers in the sauna two different ways, either wireless via the Bluetooth receiver or by directly connecting your device (smart phone, tablet, laptop etc.) with a 3.5mm male to male audio cord.1. Bluetooth Mode. When you first plug the sauna into the wall outlet a beep will sound indicating the Audio circuit board in the roof has power. The circuit board's colored LED indicator lights will flash and these will continue to flash whenever the sauna is plugged into the wall outlet. To transmit audio to the sauna's speakers from your device, search for and connect your device to the 'BT Speaker' The Audio Circuit Board is shown inside the sauna roof in Bluetooth Mode without an audio cord connected.
2. Direct Connect Mode (NO Bluetooth) First, remove the access panels from the roof by unscrewing wood screws. Connect your device to the sauna's audio system by inserting a 3.5 mm male to male audio cord into the BT circuit board as shown (Audio cords not included).To completely eliminate the RF Bluetooth signal, simply remove the Bluetooth module from the circuit board as shown www.SunStreamSaunas.com 1 - 888 262 4477
Reinstall the roof panels and feed your audio cord through the hole in roof.www.SunStreamSaunas.com 1 - 888 262 4477Enjoy your favorite audio while relaxing in your new sauna!
www.SunStreamSaunas.com 1 - 888 262 4477 Floor Heater and General MaintenanceIt is inevitable that you will drip some sweat down through the floor grate and on to the floorheater panel. Try to minimize this by wiping sweat from your body regularly during your saunasession.The floor heater can be used with or without a SMALL towel under your feet. SweatAlways sit on a towel on the sauna benchand wipe yourself down with a smalltowel to contain your sweat. This willminimize staining of the wood surfaces inthe sauna.
www.SunStreamSaunas.com 1 - 888 262 4477 XCAUTION: DO NOT useLARGE towels on the floorheater that cover any morethan 30% of the floor heater.SMALL towel only.Floor Heater CleaningSimply tilt the floor grate up to accessthe floor heater. Gently wipe theheater with a damp cloth to clean. A bit of dish soap can be used on thefloor heater if necessary. DO NOT scrub the heater withexcessive pressure. Follow the same guidlines for cleaningthe wall heater panels.
www.SunStreamSaunas.com1-888 262 4477Remove the floor heater guard.The floor heater panel is held in place with 4 wood pieces forshipping purposes. Remove these once the sauna is assembled.Floor HeaterDrip TrayRemove the 4 wood pieces with a Phillipsscrewdriver. Place a sheet of paper or similar on theheater surface to prevent scuffing of the heater whileyou turn out the screws.Keep the 4 wood pieces and screws and reinstallif you disassemble and move the sauna.In the case of spilled water on the floorheater or if you allow excessive sweat todrip on the floor heater panel, the heatercan be lifted to clean underneath. Use theincluded suction cup to grab hold of theheater panel and gently lift upward.
www.SunStreamSaunas.com1-888 262 4477Carefully tilt the heater panel back and flip itupside down. Take care not to pull on theelectrical wiring as you flip the heater.If extra slack is necessary, thewiring can be gently pulled out from under the floor base.IMPORTANT: Tuck these wiresback into the hole before flippingthe heater back into place. The stainless steel drip tray under theheater can be wiped clean with a dampcloth and gentle cleaner.
www.SunStreamSaunas.com 1 - 888 262 4477 Control Panel
Interior Control Panel Temperature Sensor FRAGILE DO NOT TOUCHwww.SunStreamSaunas.com 1 - 888 262 4477
Connecting the sauna to your house power supply When the sauna is plugged into you wall outlet the red Power Indicator light on the control panel will be on. The Bluetooth audio receiver on the roof will make a beeping noise its indicator light will turn on. ON/OFF for Heaters Push the POWER button to turn the sauna heaters ON. The various displays will come on. The sauna heaters will remain ON until the timer runs down to 00. The sauna heaters can be turned OFF at any time by pushing the POWER button. Timer Adjustment The default time is 60 minutes. Press + or - to change the Timer setting. The maximum setting is 60 minutes. The minimum setting is 5 minutes. Pre Heat Sun Stream Infrared Saunas are typically used by preheating the sauna for 20-30 minutes. Thermostat Adjustment Press + or - to change the Thermostat setting. Increase Thermostat Setting: Press the + button to increase the temperature by 1 degree C increments. The maximum setting is 65 C. Decrease Thermostat Setting: Press the - button to decrease the temperature by 1 degree C increments. The minimum setting is 25 C. www.SunStreamSaunas.com 1 - 888 262 4477 Celcius to FahrenheitTo switch from Celcius to Fahrenheit, push the 2 temperature adjustment buttons (+ -) at the same time
Thermometer /Thermostat Display When the POWER button is turned ON the digital display will show the Thermometer reading. Anytime the + and - buttons are pushed the Thermostat setting display will show. After setting the thermostat the display will return to displaying Thermometer reading. Temperature Control When the interior air temperature is below the Thermostat set temperature, the heaters will remain ON. When the interior temperature is higher than the Thermostat set temperature, the power to theheaters will be turned OFF. The heater panels will begin to cool down, air temperature and Infrared levels will slowly drop until the Thermostat is activated and the power to the heaters will be turned back on. AII (Adjustable Infrared Intensity) The Intensity button on the control panel will adjust the Infrared intensity much like a dimmer switch for a household light. Press the Intensity button to select 100%, 75% or 50 % levels of Infrared intensity for different purposes and individual needs. www.SunStreamSaunas.com 1 - 888 262 4477
www.SunStreamSaunas.com 1 - 888 262 4477 CupholderMany of our customers simply set the cup holderon the bench of the sauna. In the Evolve 10, 20and 30 saunas, the cup holder can be mountedon the side wall under the heater panels. Besure to drill pilot holes first for the wood screwsto mount cup holder to the T&G wall boards. BackrestsYour new Sun Stream Saunacomes equipped withbackrests constructed fromWestern Red Cedar. Positionthe backrest as pictured toprovide lower back supportand to position yourself acomfortable distance from theInfrared heater panels.AccessoriesAromatherapyEnjoy the aroma of your favorite essential oils,such as eucalyptus or lavender, while in thesauna. Add water and a few drops of youressential oil to the aromatherapy glass which canbe hung on the wall heater guard.
www.SunStreamSaunas.com 1 - 888 262 4477 Enjoy your Free BonusGift Sauna Accessories !! Sun Stream Plush Spa TowelSun Stream Dry Skin BrushSun Stream Pure Wool Felt Sauna Hat
www.SunStreamSaunas.com 1 - 888 262 4477 Enjoy your new Sun Stream 'Evolve' Infrared Sauna