Return to flip book view

www.SunStreamSaunas.com 1 - 888 262 4477 Assembly Manual

Prepare the Sauna Floor If you are assembling your sauna on a hard surface floor it is recommended that you apply the included, adhesive felt to the bottom of the sauna floor. www.SunStreamSaunas.com 1 - 888 262 4477

PLEASE NOTE: It is important that the sauna floor is level. Checking with a large level is recommended. If the floor is not level, shimming or other remedies should be applied before assembling the sauna. Place the sauna floor in the desired location. It is necessary to position the floor out from your walls for assembly and slide the sauna into position following assembly. www.SunStreamSaunas.com 1 - 888 262 4477

Position the Back Wall Lift the back wall into position carefully lowering the bottom of the wall into the channel on the floor base. www.SunStreamSaunas.com 1 - 888 262 4477 Position the first Side Wall Lift one of the side walls (left or right) into position wedging the bottom of the wall into the channel in the floor base.

Connect Side & Back Wall Cinch the two walls together by applying pressure on the outside of the Side Wall with your knee. It is helpful if a second person applies pressure against the opposite edge of the Back Wall. This will ensure that the two walls remain in contact and the fasteners will connect. Slide the Side Wall upward approx 3/4" while holding the Back Wall down. The 2 sets of fasteners will connect when the Side Wall is raised sufficiently. When you feel the fasteners connect, slide the Side Wall back down NOTE: It is NOT necessary to lift the entire Side Wall. Simply slide the Side Wall upward at the back corner of the sauna to connect to the Back Wall2 Sets of Tab & Keyhole fasteners connect the walls togetherwww.SunStreamSaunas.com 1 - 888 262 4477

Connect Second Side Wall Repeat the procedure for the second Side Wall Check to ensure that both sets of fasteners have connected by looking at the corner inside of the sauna. It is possible to connect one set of fasteners and miss the other. If there is an obvious gap in the corner between the two walls, the fasteners have not connected and the raising and lowering procedure will need to be repeated.www.SunStreamSaunas.com 1 - 888 262 4477

Position the Front WallLift the Front Wall into positioncarefully lowering the bottom ofthe wall into the channel on thefloor base. Prop up one end of the Front Wallto enable connection of the doorheater electrical lead.Remove protective wood stripsfrom Front Wall frameEnsure that the door heater electrical isprotruding from bottom of Front Wallframe www.SunStreamSaunas.com 1 - 888 262 4477NOTE: The Front Wall must besupported until the roof is in place.

Connect door heater electrical lead tothe floor base. NOTE:Be sure that the wire's connector is fullyinserted into the floor base connectorand that the threaded cuff is fullyscrewed onto the floor base connector. www.SunStreamSaunas.com 1 - 888 262 4477Pull the single plastic connectordown and out of the roof beforelifting the roof into place. If you are unable to grab hold ofthe connector through the smallopening in the ceiling, it may benecessary to remove the firstT&G board on the top left side ofthe roof and feed the connectordown through the opening.

Install the Sauna RoofIt can be helpful to have a third personhelping to put the roof in place Lift the roof up and over top of thesauna walls. If you are installing thesauna in a restrictive space and areunable to walk down the sides of thesaunas, it may be necessary for oneperson to go inside the sauna. Hook the right side corners of the roofover the walls then lower the rooftoward the left of the sauna.NOTE: The Front Wall must be supported until the roof is in place.www.SunStreamSaunas.com 1 - 888 262 4477Connect the 12 Volt powersupply wire at the back leftcorner of the sauna. This wire brings power to theroof for the stereo and lightingcomponents . Lower the roof on to the walls

4 Furniture BoltsScrew 2 furniture bolts through theFront Wall frame into the Floor Baseand 2 furniture bolts through theFront Wall into the Roof. The furniture bolts will require eithera Phillips head screwdriver OR theallen key included with the saunaaccessories.www.SunStreamSaunas.com 1 - 888 262 4477Side Wall GlassInstall the large Side Wall glasspanel. Glass etching is intendedto face inward.

Front Wall GlassInstall small Front Wall glass panelProtect Floor BasePlace a business card or similar onthe floor base before installing glasspanelswww.SunStreamSaunas.com 1 - 888 262 4477

Install Corner Seal StripsPress the U channel strip firmlyon to the edge of the frontglass panel. Glass Glazing StripsThere are 4 strips of flexible glazing material included with your Evolve 15 sauna.These hold the glass panels snugly in the wooden frame.It may not be necessary to use the glazing strips,or not necessary to use the entire length of thestrip, if the glass panels are a snug fit in thewooden frame. If required, install the glazing strip by firmlypressing it into the channel along side theglass panel. The glazing can be installed on the inside or outside of the glass panels. A small wooden wedge is included with yoursauna to help push the glazing strip into thechannel.www.SunStreamSaunas.com 1 - 888 262 4477Corner Seal Strips & Glazing StripsInstallation of these items can be done at this point in the saunaassembly or left as the final task.

Under-Bench Electrical NOTE: Do not connect main power cord to your wall outlet yet at this time. Power Supply CordFeed the main power supply cord in through the hole in back wall and insert in to the powersupply box. DO NOT plug power cord into your wall outlet until all electrical connections arecomplete inside of the sauna. www.SunStreamSaunas.com 1 - 888 262 4477Connect the circular connector topower supply box. Align thegroove in connector to properlyinsert. Thread the cuff ofconnector on fully. Attach the 'D-Sub' computer style connector as shown. Plug in all heater leads to the receptacleson top of the power supply box.

www.SunStreamSaunas.com 1 - 888 262 4477Remove Side Wall Heater GuardsThe wooden lattice work in front of the heaters is referred toas the heater guard. These are held on with strong magnets.It is necessary to remove the heater guards from the two sidewalls in order to install the leg heater and the sauna bench.Leg HeaterInstall the leg heater bylowering it into the bracketsmounted on the side walls.Plug leg heater into thepower supply box in floor.Install BenchThe bench in your new sauna isreversible. Choose whicheverside appeals to you to faceupward.Reinstall the Side Wall heater guardsfield mitigation system.sauna bench is part of the Evolve EHS electricThe metal shielding on the underside of the

www.SunStreamSaunas.com1-888 262 4477The metal shielding on the underside of thesauna bench is part of the Evolve EHS electricfield mitigation system.When installing the bench connect the yellow,green striped wire with its mate from the powersupply box. This is simply a grounding wire anddoes not carry any mains power. Side Wall heater guardsReinstall theInstall the benchWhen installing the bench connect the yellow, green striped wire with its mate from the power supply box. This is simply a grounding wire and does not carry any mains power.

www.SunStreamSaunas.com 1 - 888 262 4477Install the Door HandleThe Chromatherapy LEDpanel is controlled by theremote control andis NOT connected to thesauna wall control panel.

www.SunStreamSaunas.com 1 - 888 262 4477 Heater GuardsThe heater guards in your new Sun Stream Infrared Sauna are held to the wall withstrong earth magnets. If preferred, the heater guards can be screwed directly to the wallfor a more permanent and secure attachment. The heater guards are pre-drilled for theattachment screws.Screws are included to attach the heater guard to the wall. Select a drillbit with a smaller diameter than the screw threads to drill a pilot hole

www.SunStreamSaunas.com 1 - 888 262 4477 Drill a pilot hole into the wall throughthe holes in the heater guards.Do notdrill deeper than necessary for thelength of the screw. NOTE: The pilot holes are importantto ensure that the tongue and groovewall boards do not split wheninstalling screws.Install screws to firmly attach heater guard to the wall

www.SunStreamSaunas.com 1 - 888 262 4477 Ensure that the legs' ends are flushwith the bottom edge of the framesConnect bench legs to the insidecorners of the frames using suppliedwood screws.Attach the leg assembly to the bottom of the bench surface.Choosewhich surface of the bench you prefer to be the top and bottom.Option-L Movable Bench Assembly

www.SunStreamSaunas.com 1 - 888 262 4477Audio System Music can be piped to the speakers in the sauna two different ways, either wireless via the Bluetooth receiver or by directly connecting your device (smart phone, tablet, laptop etc.) with a 3.5mm male to male audio cord.1. Bluetooth Mode. When you first plug the sauna into the wall outlet a beep will sound indicating the Audio circuit board in the roof has power. The circuit board's colored LED indicator lights will flash and these will continue to flash whenever the sauna is plugged into the wall outlet. To transmit audio to the sauna's speakers from your device, search for and connect your device to the 'BT Speaker' The Audio Circuit Board is shown inside the sauna roof in Bluetooth Mode without an audio cord connected.

2. Direct Connect Mode (NO Bluetooth) First, remove the access panels from the roof by unscrewing wood screws. Connect your device to the sauna's audio system by inserting a 3.5 mm male to male audio cord into the BT circuit board as shown (Audio cords not included).To completely eliminate the RF Bluetooth signal, simply remove the Bluetooth module from the circuit board as shown www.SunStreamSaunas.com 1 - 888 262 4477

Reinstall the roof panels and feed your audio cord through the hole in roof.www.SunStreamSaunas.com 1 - 888 262 4477Enjoy your favorite audio while relaxing in your new sauna!

www.SunStreamSaunas.com 1 - 888 262 4477 Floor Heater and General MaintenanceIt is inevitable that you will drip some sweat down through the floor grate and on to the floorheater panel. Try to minimize this by wiping sweat from your body regularly during your saunasession.The floor heater can be used with or without a SMALL towel under your feet. SweatAlways sit on a towel on the sauna benchand wipe yourself down with a smalltowel to contain your sweat. This willminimize staining of the wood surfaces inthe sauna.

www.SunStreamSaunas.com 1 - 888 262 4477 XCAUTION: DO NOT useLARGE towels on the floorheater that cover any morethan 30% of the floor heater.SMALL towel only.Floor Heater CleaningSimply tilt the floor grate up to accessthe floor heater. Gently wipe theheater with a damp cloth to clean. A bit of dish soap can be used on thefloor heater if necessary. DO NOT scrub the heater withexcessive pressure. Follow the same guidlines for cleaningthe wall heater panels.

www.SunStreamSaunas.com1-888 262 4477Remove the floor heater guard.The floor heater panel is held in place with 4 wood pieces forshipping purposes. Remove these once the sauna is assembled.Floor HeaterDrip TrayRemove the 4 wood pieces with a Phillipsscrewdriver. Place a sheet of paper or similar on theheater surface to prevent scuffing of the heater whileyou turn out the screws.Keep the 4 wood pieces and screws and reinstallif you disassemble and move the sauna.In the case of spilled water on the floorheater or if you allow excessive sweat todrip on the floor heater panel, the heatercan be lifted to clean underneath. Use theincluded suction cup to grab hold of theheater panel and gently lift upward.

www.SunStreamSaunas.com1-888 262 4477Carefully tilt the heater panel back and flip itupside down. Take care not to pull on theelectrical wiring as you flip the heater.If extra slack is necessary, thewiring can be gently pulled out from under the floor base.IMPORTANT: Tuck these wiresback into the hole before flippingthe heater back into place. The stainless steel drip tray under theheater can be wiped clean with a dampcloth and gentle cleaner.

www.SunStreamSaunas.com 1 - 888 262 4477 Control Panel

Interior Control Panel Temperature Sensor FRAGILE DO NOT TOUCHwww.SunStreamSaunas.com 1 - 888 262 4477

Connecting the sauna to your house power supply When the sauna is plugged into you wall outlet the red Power Indicator light on the control panel will be on. The Bluetooth audio receiver on the roof will make a beeping noise its indicator light will turn on. ON/OFF for Heaters Push the POWER button to turn the sauna heaters ON. The various displays will come on. The sauna heaters will remain ON until the timer runs down to 00. The sauna heaters can be turned OFF at any time by pushing the POWER button. Timer Adjustment The default time is 60 minutes. Press + or - to change the Timer setting. The maximum setting is 60 minutes. The minimum setting is 5 minutes. Pre Heat Sun Stream Infrared Saunas are typically used by preheating the sauna for 20-30 minutes. Thermostat Adjustment Press + or - to change the Thermostat setting. Increase Thermostat Setting: Press the + button to increase the temperature by 1 degree C increments. The maximum setting is 65 C. Decrease Thermostat Setting: Press the - button to decrease the temperature by 1 degree C increments. The minimum setting is 25 C. www.SunStreamSaunas.com 1 - 888 262 4477 Celcius to FahrenheitTo switch from Celcius to Fahrenheit, push the 2 temperature adjustment buttons (+ -) at the same time

Thermometer /Thermostat Display When the POWER button is turned ON the digital display will show the Thermometer reading. Anytime the + and - buttons are pushed the Thermostat setting display will show. After setting the thermostat the display will return to displaying Thermometer reading. Temperature Control When the interior air temperature is below the Thermostat set temperature, the heaters will remain ON. When the interior temperature is higher than the Thermostat set temperature, the power to theheaters will be turned OFF. The heater panels will begin to cool down, air temperature and Infrared levels will slowly drop until the Thermostat is activated and the power to the heaters will be turned back on. AII (Adjustable Infrared Intensity) The Intensity button on the control panel will adjust the Infrared intensity much like a dimmer switch for a household light. Press the Intensity button to select 100%, 75% or 50 % levels of Infrared intensity for different purposes and individual needs. www.SunStreamSaunas.com 1 - 888 262 4477

www.SunStreamSaunas.com 1 - 888 262 4477 CupholderMany of our customers simply set the cup holderon the bench of the sauna. In the Evolve 10, 20and 30 saunas, the cup holder can be mountedon the side wall under the heater panels. Besure to drill pilot holes first for the wood screwsto mount cup holder to the T&G wall boards. BackrestsYour new Sun Stream Saunacomes equipped withbackrests constructed fromWestern Red Cedar. Positionthe backrest as pictured toprovide lower back supportand to position yourself acomfortable distance from theInfrared heater panels.AccessoriesAromatherapyEnjoy the aroma of your favorite essential oils,such as eucalyptus or lavender, while in thesauna. Add water and a few drops of youressential oil to the aromatherapy glass which canbe hung on the wall heater guard.

www.SunStreamSaunas.com 1 - 888 262 4477 Enjoy your Free BonusGift Sauna Accessories !! Sun Stream Plush Spa TowelSun Stream Dry Skin BrushSun Stream Pure Wool Felt Sauna Hat

www.SunStreamSaunas.com 1 - 888 262 4477 Enjoy your new Sun Stream 'Evolve'Infrared Sauna