www.SunStreamSaunas.com 1 - 888 262 4477 Assembly Manual
Prepare the Sauna FloorIf you are assembling your sauna on a hardsurface floor it is recommended that youapply the included adhesive felt to thebottom of the sauna floor.www.SunStreamSaunas.com 1 - 888 262 4477
www.SunStreamSaunas.com 1 - 888 262 4477 Place the sauna Floor Base in the desired location. It is necessary to position the floor outfrom your walls for assembly and move the sauna following assembly. PLEASE NOTE: It is important that the sauna floor is level. Checking with a largelevel is recommended. If the floor is not level, shimming or other remedies shouldbe applied before assembling the sauna.
Position the Front WallLift the front wall into position carefully lowering the bottom of the wall into the channelon the floor base. Prop up one end of the front wall to enable connection of the doorheater electrical lead.Front Wall InstallationEnsure that the door heater electrical isprotruding from bottom of front wall framewww.SunStreamSaunas.com 1 - 888 262 4477
Connect door heater electrical lead to the floor base.Ensure hat the threaded cuff is fully screwedonto the floor base connector.NOTE:Be sure that the wire's connector is fullyinserted into the floor base connector andthat the threaded cuff is fully screwedonto the floor base connector.4 Furniture BoltsScrew the 2 furniture bolts through theFront Wall frame into Floor BaseThe furniture bolts will require eithera Phillips head screwdriver OR theallen key included with the saunaaccessories. There are also 2 furniture bolts to gothrough the Front Wall and thread into theRoof later in the assembly.www.SunStreamSaunas.com 1 - 888 262 4477
Protect Floor BaseAs a precaution to protect the floor base, placea business card or similar on the floor basebefore installing glass panelInstall Right Side FrontWall Glass Panelwww.SunStreamSaunas.com 1 - 888 262 4477
Connect Side Wall to Front WallInsert Side Wall into the channel of floor base while aligningthe slot in Side Wall with edge of Front Wall glass panel. USE EXTRA CARE fitting the Side Wall to the glasspanel www.SunStreamSaunas.com 1 - 888 262 4477
Back WallInsert back wall intochannel of floor basewww.SunStreamSaunas.com 1 - 888 262 4477 SIDEWALL Wood ScrewUse the supplied wood screw and thepre-drilled hole to secure the Side Wallto the Front Wall frame.
Connect the Back Wall toSide Wall Cinch the two walls togetherby applying pressure on theoutside of the Side Wall withthe inside of your knee.Slide the Back Wall up approx. 3/4” while holdingthe Side Wall down with your opposite hand.The 2 sets of fasteners for the walls will connectwhen the back wall is raised sufficiently. Whenyou feel the fasteners connect, slide the BackWall back down.NOTE: It is NOT necessary to lift the entireBack Wall. Simply slide the Back Wall upwardat the back corner of the sauna to connect tothe Side Wall It is helpful if a second person applies pressure against the opposite edge of the back wall.This will helps ensure that the two walls remain in contact and the fasteners will connect. www.SunStreamSaunas.com 1 - 888 262 4477
Second Front Glass PanelUse the same procedure asfor the first glass panel There are two sets of fasteners to join the saunas' back corners together. After loweringthe Back Wall, check to ensure that both sets of fasteners have connected by looking atthe corner inside of the sauna. It is possible to connect one set of fasteners and miss theother. If there is an obvious gap in the corner between the two walls the fasteners havenot connected and the raising and lowering procedure will need to be repeated.www.SunStreamSaunas.com 1 - 888 262 4477
Connect the second Side Wall to the Back and Front WallUse supplied wood screw and pre-drilled hole to secure the top of the sidewall to the front wall frame.www.SunStreamSaunas.com 1 - 888 262 4477 Insert the Left Side Wall into thechannel of floor base whilealigning the slot in Side Wall withedge of Front Wall glass panel. USE EXTRA CARE fitting theSide Wall to the glass panelWood ScrewUse the supplied wood screw and thepre-drilled hole to secure the Left SideWall to the Front Wall frame.SIDE WALL
Install the Sauna RoofLift the roof up and over top of thesauna walls. If you are installingthe sauna in a restrictive spaceand are unable to walk down thesides of the saunas, it may benecessary for one person to goinside the sauna. Hook the right side corners of theroof over the walls then lower theroof toward the left of the sauna.www.SunStreamSaunas.com 1 - 888 262 4477 Pull the single plastic connectordown and out of the roof beforelifting the roof into place.If you are unable to grab hold ofthe connector through the smallopening in the ceiling, it may benecessary to remove the firstT&G board on the top left side ofthe roof and feed the connectordown through the opening.
www.SunStreamSaunas.com 1 - 888 262 4477 Connect the 12 Volt power supplywire at the back left corner of thesauna. This wire brings power to the rooffor the stereo and lightingcomponents. Lower the roof on to the wallsUnder-Bench ElectricalNOTE: Do not connect main power cord to your wall outlet yet at this time.Connect the circular connector topower supply box. Align thegroove in connector to properlyinsert. Thread the cuff ofconnector on fully.Attach the 'D-Sub' computerstyle connector as shown.Plug in all heater leads to the receptacleson top of the power supply box.
Power Supply CordFeed the main power supply cord in through the hole in back wall and insert in to the powersupply box. DO NOT plug power cord into your wall outlet until all electrical connections arecomplete inside of the sauna.Door Heater ElectricalConnect the coiled wire from the door heaterto the connector on the door frame.Ensure that the connector is fully inserted andthe threaded cuff is fully screwed on to thedoor frame connector.www.SunStreamSaunas.com 1 - 888 262 4477
Remove Side Wall HeaterGuardsThe wooden lattice work in frontof the heaters is referred to asthe heater guards. These areheld on with strong magnets. It isnecessary to remove the heaterguards from the two side walls inorder to install the sauna bench.www.SunStreamSaunas.com 1 - 888 262 4477 Leg HeaterInstall the leg heater bylowering it into the bracketsmounted on the side walls.Plug leg heater into thepower supply box in floor.
www.SunStreamSaunas.com1-888 262 4477The metal shielding on the underside of thesauna bench is part of the Evolve EHS electricfield mitigation system.When installing the bench connect the yellow,green striped wire with its mate from the powersupply box. This is simply a grounding wire anddoes not carry any mains power.
www.SunStreamSaunas.com 1 - 888 262 4477 Install BenchThe bench in your new sauna isreversible. Choose whicheverside appeals to you to face upward.Reinstall theSide Wall heater guardsInstall the Door Handle
www.SunStreamSaunas.com 1 - 888 262 4477 Glass Glazing StripsThere are 4 strips of flexible glazingmaterial included with your Evolve 20sauna. These hold the glass panelssnugly in the wooden frame. It may not be necessary to use theglazing strips, or not necessary to use theentire length of the strip, if the glasspanels are a snug fit in the woodenframe. If required, install the glazing stripby firmly pressing it into the channelalong side the glass panel. The glazingcan be installed on the inside or outsideof the glass panels A small wooden wedge is included tohelp push the glazing strip into thechannel.The Chromatherapy LED panel is controlled by the remote control and isNOT connected to the sauna wall control panel.
www.SunStreamSaunas.com 1 - 888 262 4477 Heater GuardsThe heater guards in your new Sun Stream Infrared Sauna are held to the wall withstrong earth magnets. If preferred, the heater guards can be screwed directly to the wallfor a more permanent and secure attachment. The heater guards are pre-drilled for theattachment screws.Screws are included to attach the heater guard to the wall. Select a drillbit with a smaller diameter than the screw threads to drill a pilot hole
www.SunStreamSaunas.com 1 - 888 262 4477 Drill a pilot hole into the wall throughthe holes in the heater guards.Do notdrill deeper than necessary for thelength of the screw. NOTE: The pilot holes are importantto ensure that the tongue and groovewall boards do not split wheninstalling screws.Install screws to firmly attach heater guard to the wall
www.SunStreamSaunas.com 1 - 888 262 4477 Ensure that the legs' ends are flushwith the bottom edge of the framesConnect bench legs to the insidecorners of the frames using suppliedwood screws.Attach the leg assembly to the bottom of the bench surface.Choosewhich surface of the bench you prefer to be the top and bottom.Option-L Movable Bench Assembly
www.SunStreamSaunas.com 1 - 888 262 4477Audio System Music can be piped to the speakers in the sauna two different ways, either wireless via the Bluetooth receiver or by directly connecting your device (smart phone, tablet, laptop etc.) with a 3.5mm male to male audio cord.1. Bluetooth Mode. When you first plug the sauna into the wall outlet a beep will sound indicating the Audio circuit board in the roof has power. The circuit board's colored LED indicator lights will flash and these will continue to flash whenever the sauna is plugged into the wall outlet. To transmit audio to the sauna's speakers from your device, search for and connect your device to the 'BT Speaker' The Audio Circuit Board is shown inside the sauna roof in Bluetooth Mode without an audio cord connected.
2. Direct Connect Mode (NO Bluetooth) First, remove the access panels from the roof by unscrewing wood screws. Connect your device to the sauna's audio system by inserting a 3.5 mm male to male audio cord into the BT circuit board as shown (Audio cords not included).To completely eliminate the RF Bluetooth signal, simply remove the Bluetooth module from the circuit board as shown www.SunStreamSaunas.com 1 - 888 262 4477
Reinstall the roof panels and feed your audio cord through the hole in roof.www.SunStreamSaunas.com 1 - 888 262 4477Enjoy your favorite audio while relaxing in your new sauna!
www.SunStreamSaunas.com 1 - 888 262 4477 Floor Heater and General MaintenanceIt is inevitable that you will drip some sweat down through the floor grate and on to the floorheater panel. Try to minimize this by wiping sweat from your body regularly during your saunasession.The floor heater can be used with or without a SMALL towel under your feet. SweatAlways sit on a towel on the sauna benchand wipe yourself down with a smalltowel to contain your sweat. This willminimize staining of the wood surfaces inthe sauna.
www.SunStreamSaunas.com 1 - 888 262 4477 XCAUTION: DO NOT useLARGE towels on the floorheater that cover any morethan 30% of the floor heater.SMALL towel only.Floor Heater CleaningSimply tilt the floor grate up to accessthe floor heater. Gently wipe theheater with a damp cloth to clean. A bit of dish soap can be used on thefloor heater if necessary. DO NOT scrub the heater withexcessive pressure. Follow the same guidlines for cleaningthe wall heater panels.
www.SunStreamSaunas.com1-888 262 4477Remove the floor heater guard.The floor heater panel is held in place with 4 wood pieces forshipping purposes. Remove these once the sauna is assembled.Floor HeaterDrip TrayRemove the 4 wood pieces with a Phillipsscrewdriver. Place a sheet of paper or similar on theheater surface to prevent scuffing of the heater whileyou turn out the screws.Keep the 4 wood pieces and screws and reinstallif you disassemble and move the sauna.In the case of spilled water on the floorheater or if you allow excessive sweat todrip on the floor heater panel, the heatercan be lifted to clean underneath. Use theincluded suction cup to grab hold of theheater panel and gently lift upward.
www.SunStreamSaunas.com1-888 262 4477Carefully tilt the heater panel back and flip itupside down. Take care not to pull on theelectrical wiring as you flip the heater.If extra slack is necessary, thewiring can be gently pulled out from under the floor base.IMPORTANT: Tuck these wiresback into the hole before flippingthe heater back into place. The stainless steel drip tray under theheater can be wiped clean with a dampcloth and gentle cleaner.
www.SunStreamSaunas.com 1 - 888 262 4477 Control Panel
Interior Control Panel Temperature Sensor FRAGILE DO NOT TOUCHwww.SunStreamSaunas.com 1 - 888 262 4477
Connecting the sauna to your house power supply When the sauna is plugged into you wall outlet the red Power Indicator light on the control panel will be on. The Bluetooth audio receiver on the roof will make a beeping noise its indicator light will turn on. ON/OFF for Heaters Push the POWER button to turn the sauna heaters ON. The various displays will come on. The sauna heaters will remain ON until the timer runs down to 00. The sauna heaters can be turned OFF at any time by pushing the POWER button. Timer Adjustment The default time is 60 minutes. Press + or - to change the Timer setting. The maximum setting is 60 minutes. The minimum setting is 5 minutes. Pre Heat Sun Stream Infrared Saunas are typically used by preheating the sauna for 20-30 minutes. Thermostat Adjustment Press + or - to change the Thermostat setting. Increase Thermostat Setting: Press the + button to increase the temperature by 1 degree C increments. The maximum setting is 65 C. Decrease Thermostat Setting: Press the - button to decrease the temperature by 1 degree C increments. The minimum setting is 25 C. www.SunStreamSaunas.com 1 - 888 262 4477 Celcius to FahrenheitTo switch from Celcius to Fahrenheit, push the 2 temperature adjustment buttons (+ -) at the same time
Thermometer /Thermostat Display When the POWER button is turned ON the digital display will show the Thermometer reading. Anytime the + and - buttons are pushed the Thermostat setting display will show. After setting the thermostat the display will return to displaying Thermometer reading. Temperature Control When the interior air temperature is below the Thermostat set temperature, the heaters will remain ON. When the interior temperature is higher than the Thermostat set temperature, the power to theheaters will be turned OFF. The heater panels will begin to cool down, air temperature and Infrared levels will slowly drop until the Thermostat is activated and the power to the heaters will be turned back on. AII (Adjustable Infrared Intensity) The Intensity button on the control panel will adjust the Infrared intensity much like a dimmer switch for a household light. Press the Intensity button to select 100%, 75% or 50 % levels of Infrared intensity for different purposes and individual needs. www.SunStreamSaunas.com 1 - 888 262 4477
www.SunStreamSaunas.com 1 - 888 262 4477 CupholderMany of our customers simply set the cup holderon the bench of the sauna. In the Evolve 10, 20and 30 saunas, the cup holder can be mountedon the side wall under the heater panels. Besure to drill pilot holes first for the wood screwsto mount cup holder to the T&G wall boards. BackrestsYour new Sun Stream Saunacomes equipped withbackrests constructed fromWestern Red Cedar. Positionthe backrest as pictured toprovide lower back supportand to position yourself acomfortable distance from theInfrared heater panels.AccessoriesAromatherapyEnjoy the aroma of your favorite essential oils,such as eucalyptus or lavender, while in thesauna. Add water and a few drops of youressential oil to the aromatherapy glass which canbe hung on the wall heater guard.
www.SunStreamSaunas.com 1 - 888 262 4477 Enjoy your Free BonusGift Sauna Accessories !! Sun Stream Plush Spa TowelSun Stream Dry Skin BrushSun Stream Pure Wool Felt Sauna Hat
www.SunStreamSaunas.com 1 - 888 262 4477 Enjoy your new Sun Stream 'Evolve 20' Infrared Sauna