www.SunStreamSaunas.com1-888 262 4477 Assembly Manual
Prepare & Position the Sauna FloorIf you are assembling your sauna on a hard surface floor it is recommended that you apply the includedadhesive felt to the bottom of the sauna floor. Place the sauna floor in the desired location. It is necessary to position the floor out from your walls forassembly and move the sauna following assembly.Please note: It is important that the sauna floor is level. Checking with a large level isrecommended. If the floor is not level, shimming or other remedies should be applied beforeassembling the sauna.www.SunStreamSaunas.com1-888 262 4477
Position the Back WallLift the back wall into position carefullylowering the bottom of the wall into thechannel on the floor base. www.SunStreamSaunas.com1-888 262 4477 Position Right Side WallLift the Right side wall into positionwedging the bottom of the wall into thechannel in the floor base.
Back Right Corner WallCinch the Right Side wall and the Back walltogether by applying pressure on theoutside of the Side wall. Slide the Right Side wall upward approx.1/2” while holding the back wall downIt is helpful if a second person applies pressure against the opposite edge of the back wall. This will helpensure that the two walls remain in contact and the fasteners connect. The 2 sets of fasteners for the walls will connect whenthe side wall is raised sufficiently. Slide the Side Wall down while continuing to cinch thetwo walls together.www.SunStreamSaunas.com1-888 262 4477 NOTE: It is NOT necessary to lift theentire Side Wall. Simply slide the RightSide wall upward at the back corner ofthe sauna.Back Wall Held DownSide Wall Up
www.SunStreamSaunas.com1-888 262 4477 There are two sets of fasteners to join the saunas' corners together. After lowering the Side Wall, check toensure that both sets of fasteners have connected by looking at the corner inside of the sauna. It is possible toconnect one set of fasteners and miss the other. If there is an obvious gap in the corner between the two wallsat least one fastener has not connected and the raising and lowering procedure will need to be repeated. Back Left CornerLift the Left Side Wall into position wedging the bottom of the wall into the channel in the floor base.Back WallCinch the Left Side Wall and the Back Wall together by applyingpressure on the outside of the Left Side wall. Slide the Left Side wall upward approx. 1/2” while holding the BackWall downThe 2 sets of fasteners for the walls will connect when the Side wall israised sufficiently. Slide the Left Side Wall down while continuing to cinch the two wallstogether.Back WallSide Wall
Position the Front Wall/Door FrameLift the Front Wall/Door Frame into position carefully lowering the bottom into the channel on the floor base.Prop up one end of the Front Wall/Door Frame to enable connection of the door heater electrical lead.Door Heater ElectricalEnsure that the door heater electrical is protruding frombottom of Front Wall Door frame. A bit of plastic wrap canserve to hold the connector out slightly. www.SunStreamSaunas.com1-888 262 4477NOTE: After installing the Back and 2 Side Walls, you may want to slide the sauna back into its final position beforeproceeding with Front Wall and Roof. It may be helpful to insert the main power cord through the hole in BackWall before sliding the sauna back against your homes wall. Move the sauna by pushing horizontally on theFloor Base. DO NOT push upward on the Walls as they are not mechanically connected to the Floor base.
Connect door heater electrical lead to the floor base.NOTE:Be sure that the wire's connector is fully inserted into thefloor base connector and that the threaded cuff is fullyscrewed on to the floor base connector.Secure the Right WallUse the supplied wood screw and the pre-drilledhole to secure the Right Side Wall to the FrontWall/Door Frame.www.SunStreamSaunas.com1-888 262 4477Side Wall Connect the Right Side Wall to the Front WallCinch the Right Side Wall and the Front Wall togetherSlide the Right Side wall upward approx. 1/2” while holding the FrontWall down.The 2 sets of fasteners for the walls will connect when the Side wall israised sufficiently.Slide the Right Side Wall down while continuing to cinch the two wallstogether.NOTE: It is NOT necessary to lift theentire Side Wall. Simply slide the RightSide wall upward at the front corner ofthe sauna.
Install the Sauna RoofLift the Roof up and over top of the sauna walls. If you are installing the sauna in a restrictive space and areunable to walk down the sides of the saunas, it may be necessary for one person to go inside the sauna.Hook the right side corners of the Roof over the walls then lower the Roof toward the left of the sauna.Prepare to install the sauna roofPull the single plastic connector down and out of the roof before lifting theroof into place. If you are unable to grab hold of the connector through the small openingin the ceiling, it may be necessary to remove the first T&G board on thetop left side of the roof and feed the connector down through the opening. www.SunStreamSaunas.com1-888 262 4477Lower Roof into PositionIt may be necessary to push on the inside or outside of the Back and Side walls to enable to roof to drop intoposition.
Side Wall GlassInstall Side Wall glass panel.Glass etching is intended to face inward.www.SunStreamSaunas.com1-888 262 4477IMPORTANTFor temporary purposes, insert a foot or two of the flexible plasticstrip on the inside of the Side Wall glass panel. This will hold theglass panel in place and assist in the following assembly steps.
Install Front Wall Glass PanelCarefully insert the bottom edge of the Front Wall glass panel into the slot in the Floor base. The FrontWall glass panel must be positioned so that the heater panel is fitting inside of the Side Wall glass panel. www.SunStreamSaunas.com1-888 262 4477Carefully tilt the front edge of the Roofupward, about 1/2", just enough to tilt the FrontWall Glass in to position
Lower the Roof so that the Front Wallglass panel fits into the Roof slot. Install Corner SealFirmly press the corner seal on to theedge of the Front Wall glass panelwww.SunStreamSaunas.com1-888 262 4477Remove the temporary plastic glazing stripfrom the inside of Side Wall glass panel
Firmly press flexible glazing strip into wood channels along the outside of theSide and Front Wall glass panels. It may not be necessary to use the flexible glazing for the full height of theglass panels. Use the glazing strip where it fits into the channels.Small wooden block (included)can be used to fully press theglazing strip into channel Install 4 furniture bolts through topand bottom of door frame using theallan key (included) www.SunStreamSaunas.com1-888 262 4477
Connect the circular connector topower supply box. Align thegroove in connector to properlyinsert. Thread the cuff of theconnector on fully.Attach the 'D-Sub' computerstyle connector as shownPlug in all heater leads toreceptacles in the power supply box.Under-Bench ElectricalNOTE: Do not connect main power cord to your wall outlet yet at this time.www.SunStreamSaunas.com1-888 262 4477
Feed the main power supply cord in through the hole in Back Wall and insert in power supply box. Do NOT plug power cord into your wall outlet until all electrical connections are finished inside of the sauna. Connect circular connectors for the 2 Front Wall heaters. Thread the cuff of connectors on fully. When all connections are made inside of the sauna, plug thesauna's main power cord into wall outlet. www.SunStreamSaunas.com1-888 262 4477
www.SunStreamSaunas.com1-888 262 4477Remove Side Wall Heater GuardsThe wooden lattice work in front of theheaters is referred to as the heater guard. These are held on with strong magnets. It is necessary to remove the heater guardsfrom the two side walls in order to install theleg heater and the sauna bench.Install the Leg HeaterInstall the leg heater by lowering it into the bracketsmounted on the side walls.Plug the leg heater into the power supply box in floor.
www.SunStreamSaunas.com1-888 262 4477The metal shielding on the underside of thesauna bench is part of the Evolve EHS electricfield mitigation system.When installing the bench connect the yellow,green striped wire with its mate from the powersupply box. This is simply a grounding wire anddoes not carry any mains power.
www.SunStreamSaunas.com1-888 262 4477Install BenchThe bench in your new sauna isreversible. Choose whichever sideappeals to you to face upward.Reinstall the side wallheater guardsInstall the door handle
www.SunStreamSaunas.com 1 - 888 262 4477 Heater GuardsThe heater guards in your new Sun Stream Infrared Sauna are held to the wall withstrong earth magnets. If preferred, the heater guards can be screwed directly to the wallfor a more permanent and secure attachment. The heater guards are pre-drilled for theattachment screws.Screws are included to attach the heater guard to the wall. Select a drillbit with a smaller diameter than the screw threads to drill a pilot hole
www.SunStreamSaunas.com 1 - 888 262 4477 Drill a pilot hole into the wall throughthe holes in the heater guards.Do notdrill deeper than necessary for thelength of the screw. NOTE: The pilot holes are importantto ensure that the tongue and groovewall boards do not split wheninstalling screws.Install screws to firmly attach heater guard to the wall
www.SunStreamSaunas.com 1 - 888 262 4477 Ensure that the legs' ends are flushwith the bottom edge of the framesConnect bench legs to the insidecorners of the frames using suppliedwood screws.Attach the leg assembly to the bottom of the bench surface.Choosewhich surface of the bench you prefer to be the top and bottom.Option-L Movable Bench Assembly
www.SunStreamSaunas.com 1 - 888 262 4477Audio System Music can be piped to the speakers in the sauna two different ways, either wireless via the Bluetooth receiver or by directly connecting your device (smart phone, tablet, laptop etc.) with a 3.5mm male to male audio cord.1. Bluetooth Mode. When you first plug the sauna into the wall outlet a beep will sound indicating the Audio circuit board in the roof has power. The circuit board's colored LED indicator lights will flash and these will continue to flash whenever the sauna is plugged into the wall outlet. To transmit audio to the sauna's speakers from your device, search for and connect your device to the 'BT Speaker' The Audio Circuit Board is shown inside the sauna roof in Bluetooth Mode without an audio cord connected.
2. Direct Connect Mode (NO Bluetooth) First, remove the access panels from the roof by unscrewing wood screws. Connect your device to the sauna's audio system by inserting a 3.5 mm male to male audio cord into the BT circuit board as shown (Audio cords not included).To completely eliminate the RF Bluetooth signal, simply remove the Bluetooth module from the circuit board as shown www.SunStreamSaunas.com 1 - 888 262 4477
Reinstall the roof panels and feed your audio cord through the hole in roof.www.SunStreamSaunas.com 1 - 888 262 4477Enjoy your favorite audio while relaxing in your new sauna!
www.SunStreamSaunas.com 1 - 888 262 4477 Floor Heater and General MaintenanceIt is inevitable that you will drip some sweat down through the floor grate and on to the floorheater panel. Try to minimize this by wiping sweat from your body regularly during your saunasession.The floor heater can be used with or without a SMALL towel under your feet. SweatAlways sit on a towel on the sauna benchand wipe yourself down with a smalltowel to contain your sweat. This willminimize staining of the wood surfaces inthe sauna.
www.SunStreamSaunas.com 1 - 888 262 4477 XCAUTION: DO NOT useLARGE towels on the floorheater that cover any morethan 30% of the floor heater.SMALL towel only.Floor Heater CleaningSimply tilt the floor grate up to accessthe floor heater. Gently wipe theheater with a damp cloth to clean. A bit of dish soap can be used on thefloor heater if necessary. DO NOT scrub the heater withexcessive pressure. Follow the same guidlines for cleaningthe wall heater panels.
www.SunStreamSaunas.com1-888 262 4477Remove the floor heater guard.The floor heater panel is held in place with 4 wood pieces forshipping purposes. Remove these once the sauna is assembled.Floor HeaterDrip TrayRemove the 4 wood pieces with a Phillipsscrewdriver. Place a sheet of paper or similar on theheater surface to prevent scuffing of the heater whileyou turn out the screws.Keep the 4 wood pieces and screws and reinstallif you disassemble and move the sauna.In the case of spilled water on the floorheater or if you allow excessive sweat todrip on the floor heater panel, the heatercan be lifted to clean underneath. Use theincluded suction cup to grab hold of theheater panel and gently lift upward.
www.SunStreamSaunas.com1-888 262 4477Carefully tilt the heater panel back and flip itupside down. Take care not to pull on theelectrical wiring as you flip the heater.If extra slack is necessary, thewiring can be gently pulled out from under the floor base.IMPORTANT: Tuck these wiresback into the hole before flippingthe heater back into place. The stainless steel drip tray under theheater can be wiped clean with a dampcloth and gentle cleaner.
www.SunStreamSaunas.com 1 - 888 262 4477 Control Panel
Interior Control Panel Temperature Sensor FRAGILE DO NOT TOUCHwww.SunStreamSaunas.com 1 - 888 262 4477
Connecting the sauna to your house power supply When the sauna is plugged into you wall outlet the red Power Indicator light on the control panel will be on. The Bluetooth audio receiver on the roof will make a beeping noise its indicator light will turn on. ON/OFF for Heaters Push the POWER button to turn the sauna heaters ON. The various displays will come on. The sauna heaters will remain ON until the timer runs down to 00. The sauna heaters can be turned OFF at any time by pushing the POWER button. Timer Adjustment The default time is 60 minutes. Press + or - to change the Timer setting. The maximum setting is 60 minutes. The minimum setting is 5 minutes. Pre Heat Sun Stream Infrared Saunas are typically used by preheating the sauna for 20-30 minutes. Thermostat Adjustment Press + or - to change the Thermostat setting. Increase Thermostat Setting: Press the + button to increase the temperature by 1 degree C increments. The maximum setting is 65 C. Decrease Thermostat Setting: Press the - button to decrease the temperature by 1 degree C increments. The minimum setting is 25 C. www.SunStreamSaunas.com 1 - 888 262 4477 Celcius to FahrenheitTo switch from Celcius to Fahrenheit, push the 2 temperature adjustment buttons (+ -) at the same time
Thermometer /Thermostat Display When the POWER button is turned ON the digital display will show the Thermometer reading. Anytime the + and - buttons are pushed the Thermostat setting display will show. After setting the thermostat the display will return to displaying Thermometer reading. Temperature Control When the interior air temperature is below the Thermostat set temperature, the heaters will remain ON. When the interior temperature is higher than the Thermostat set temperature, the power to theheaters will be turned OFF. The heater panels will begin to cool down, air temperature and Infrared levels will slowly drop until the Thermostat is activated and the power to the heaters will be turned back on. AII (Adjustable Infrared Intensity) The Intensity button on the control panel will adjust the Infrared intensity much like a dimmer switch for a household light. Press the Intensity button to select 100%, 75% or 50 % levels of Infrared intensity for different purposes and individual needs. www.SunStreamSaunas.com 1 - 888 262 4477
www.SunStreamSaunas.com 1 - 888 262 4477 CupholderMany of our customers simply set the cup holderon the bench of the sauna. In the Evolve 10, 20and 30 saunas, the cup holder can be mountedon the side wall under the heater panels. Besure to drill pilot holes first for the wood screwsto mount cup holder to the T&G wall boards. BackrestsYour new Sun Stream Saunacomes equipped withbackrests constructed fromWestern Red Cedar. Positionthe backrest as pictured toprovide lower back supportand to position yourself acomfortable distance from theInfrared heater panels.AccessoriesAromatherapyEnjoy the aroma of your favorite essential oils,such as eucalyptus or lavender, while in thesauna. Add water and a few drops of youressential oil to the aromatherapy glass which canbe hung on the wall heater guard.
www.SunStreamSaunas.com 1 - 888 262 4477 Enjoy your Free BonusGift Sauna Accessories !! Sun Stream Plush Spa TowelSun Stream Dry Skin BrushSun Stream Pure Wool Felt Sauna Hat
Enjoy your new Sun Stream 'Evolve 30' Infrared Sauna !www.SunStreamSaunas.com1-888 262 4477